Magnavox MWC20D6 Manuel du propriétaire télécharger pdf (Page 9)

AUX

VOLUME 20

C C C C C C C C C C C C C C C C

WATCHING A TV PROGRAM

1 Press [STANDBY-ON y] to turn on the unit.

NOTES:

• If the TV screen shows snow and

there is no operation for more

than 10 seconds,

“HELPFUL HINTS” appears.

• Make sure the antenna or cable is connected

properly. (Refer to “ANTENNA/CABLE CONNEC-

TIONS on page 6.)

• Set the“AUTO CH PROGRAMMING” in the

CHANNEL SET UP. (Refer to “CHANNEL SET UP”

on page 11.)

• If those settings do not work properly, please

call our help line on the front page of this owner’s

manual.

2 Use [CH.

] or the Number buttons to

select your desired channel number.

3 Use [VOL.

] to adjust the volume.

Press

[MUTE] to instantly

mute the sound. Press it again

to restore the previous sound

level.

NOTE:

•Even if you turn off the unit in the DVD mode, the unit

will be in the TV mode when you turn it on again.

TO WATCH CABLE OR SATELLITE CHANNEL

If the unit is connected to a cable box or satellite

box, use

[CH. K / L] to select CH3 or CH4 accord-

ing to the output channel setting of the device, then

select the desired channel on that device.

TO WATCH EXTERNAL INPUT

When an external device is

connected to the front AUDIO/

VIDEO input jacks, press

[SELECT] or [CH. K / L] repeat-

edly until "AUX" appears on the

screen.

SELECT LANGUAGE

ENGLISH

NEXT:PRESS VOL

ESPAÑOL

DESPUÉS:PRESIONE VOL

FRANÇAIS

APRÈS:PRESSEZ CH.

– INITIAL SETUP –

PLEASE CONNECT ANTENNA

OR CABLE OR SATELLITE

TO THIS UNIT.

THEN PRESS PLAY,

IN ORDER TO PERFORM

“AUTO CH PROGRAMMING”

CH 15

(Example)

INITIAL SET UP

When you turn on the power for the first time,

the SELECT LANGUAGE screen is displayed.

Select the language for screen display and perform

auto programming of the channels.

1 After antenna or cable connection is

completed, connect the power cord into

a standard AC outlet.

2 Press [STANDBY-ON y] to turn on the unit.

3 Press one of the keys listed

below to select the language

of on-screen menu.

• ENGLISH :

[VOL.

]

• ESPAÑOL : [VOL.

]

• FRANÇAIS : [CH.

]

4 Confirm the antenna (or cable)

connection and press

[PLAY

• The tuner scans and memori-

zes all active channels in

your area.

5 When the scanning is comple-

ted, the tuner stops on the

lowest memorized channel.

NOTES:

•You can exit the INITIAL SETUP menu by pressing

[SET-UP]. If the button is pressed during channel

scanning, the tuner stops scanning and the lowest

memorized channel is displayed.

•

The INITIAL SETUP menu is displayed every time

you turn on the unit unless the scanning is com-

pleted.

• In case no channel can be

received by the channel scanning,

"NO TV SIGNALS" is displayed on

the screen. Turn off the unit and

check the antenna connection,

then follow steps 1 to 5 again.

•

You can change the setting after completing INI-

TIAL SET UP by LANGUAGE menu or CHANNEL

SET UP menu. (Refer to "ON-SCREEN MENU LAN-

GUAGE" or "CHANNEL SET UP" on page 11).

• If there is no signal input from the antenna terminal

and no operation for 15 minutes, the unit will turn itself

off automatically.

V OPERATION AND SETTINGS

TV SECTION

TV OPERATION AND SETTINGS

TV SECTION

o use the Number buttons

•Single digit channels: (Ex. 02, 03, 04 and so on)

Press [0] first to select a single digit channel.

•Two digit channels: (Ex. 12, 38, 95 ...)

Press two digits directly.

•Three digit channels: (Ex. 115, 125 ...)

Press

[+100] first, then press the last two digits.

NO TV SIGNALS

- HELPFUL HINTS -

1.PLEASE CHECK TO SEE IF

THE ANTENNA/CABLE/

SATELLITE IS

PROPERLY CONNECTED.

2.DID YOU PERFORM

“AUTO CH PROGRAMMING”?

3.PLEASE REFER TO FRONT

PAGE OF THE OWNER’S

MANUAL OR REAR PANEL

FOR SUPPORT LINE

INFORMATION.

T9206UG(EN).QX4 06.7.24 6:14 PM Page 9

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 35 36

Commentaires sur ces manuels

Pas de commentaire

Magnavox MWC20D6 Manuel du propriétaire Page 9

Commentaires sur ces manuels

Produits connexes et manuels pour Télévisions à tube cathodique Magnavox MWC20D6